We report on the fabrication of a chirped, phase mask that was used to create a fiber Bragg grating(FBG)device for the compensation of chromatic dispersion in longhaul optical transmission networks.Electron beamlithography was used to expose the grating onto a resist-coated quartz plate. After etching, this phase mask was used to holographically expose an index grating into the fiber core [K. O. Hill, F. Bilodeau, D. C. Johnson, and J. Albert, Appl. Phys. Lett.62, 1035 (1993)]. The linear increase in the grating period, “chirp,” is only 0.55 nm over the 10 cm grating. This is too small to be defined by computer aided design and a digital deflection system. Instead, the chirp was incorporated by repeatedly rescaling the analog electronics used for field size calibration. Special attention must be paid to minimize any field stitching and exposure artifacts. This was done by using overlapping fields in a “voting” method. As a result, each grating line is exposed by the accumulation of three overlapping exposures at 1/3 dose. This translates any abrupt stitching error into a small but uniform change in the line-to-space ratio of the grating. The phase mask was used with the double-exposure photoprinting technique [K. O. Hill, F. Bilodeau, B. Malo, T. Kitagawa, S. Thériault, D. C. Johnson, J. Albert, and K. Takiguchi, Opt. Lett. 19, 1314 (1994)]: a KrF excimer laser holographically imprints an apodized chirped Bragg grating in a hydrogen loaded SMF-28 optical fiber. Our experiments have demonstrated a spectral delay of −1311 ps/nm with a linearity of +/−10 ps over the 3 dB bandwidth of the resonant wavelength of the FBG. The reflectance, centered on 1550 nm, shows a side-lobe suppression of −25 dB. Fabrication processes and optical characterization will be discussed.
The effective indices of the cladding modes of optical fibers depend on the refractive index of the medium surrounding the fiber. We show experimentally and theoretically that while cladding modes with similar effective indices normally have similar refractometric sensitivities, the addition of a 50 nm thick gold sheath enhances the sensitivity of some EH modes by more than one order of magnitude while nearly completely suppressing the sensitivity of neighbouring HE modes (by three orders of magnitude, down to insignificant levels). A differential sensitivity of ∼1000 nm/(refractive index unit) is experimentally reported between adjacent EH and HE grating resonances.
The observation of four-wave mixing (FWM) in single-walled carbon nanotubes (SWCNTs) deposited around a tilted fiber Bragg grating (TFBG) has been demonstrated. A thin, floating SWCNT film is manually wrapped around the outer cladding of the fiber and FWM occurs between two core-guided laser signals by TFBG-induced interaction of the core mode and cladding modes. The effective nonlinear coefficient is calculated to be 1.8 10 3W -1Km -1. The wavelength of generated idlers is tunable with a range of 7.8 nm.
A photolithographic method is described for fabricating refractive index Bragg gratings in photosensitive optical fiber by using a special phase mask grating made of silica glass. A KrF excimer laser beam (249 nm) at normal incidence is modulated spatially by the phase mask grating. The diffracted light, which forms a periodic, high-contrast intensity pattern with half the phase mask grating pitch, photoimprints a refractive index modulation into the core of photosensitive fiber placed behind, in proximity, and parallel, to the mask; the phase mask grating striations are oriented normal to the fiber axis. This method of fabricating in-fiber Bragg gratings is flexible, simple to use, results in reduced mechanical sensitivity of the grating writing apparatus and is functional even with low spatial and temporal coherence laser sources.
Silica-based thin-film multilayers are investigated as a means to enhance the effective second-order nonlinearity induced in silica glass structures by corona poling. Structures consisting of phosphorus-doped and undoped silica glass layers exhibit second harmonic generation (SHG) that is higher by an order of magnitude compared to the SHG in bulk silica glass poled under the same conditions. When the poled structure consists of two multilayered stacks separated in space, the stacks exhibit comparable poling-induced nonlinearities. This result suggests that the poling voltage is divided between the two stacks such that simultaneous poling of multiple regions within the sample is realized.
Photobleaching of optical absorption bands in the 5 eV region and the creation of others at higher and lower energy have been examined in the case of ArF (6.4 eV) and KrF (5 eV) excimer laserirradiation of 3GeO2:97SiO2glasses. We report a difference in the transformation process of the neutral oxygen monovacancy and also of the germanium lone pair center (GLPC) into electron trap centers associated with fourfold coordinated Ge ions and Ge-E′ centers when we use one or the other laser. Correlations between absorption bands and electron spin resonance signals were made after different steps of laser irradiation. It was found that the KrF laser generates twice as many Ge-E′ centers as the ArF laser for the same dose of energy delivered. The main reason for this difference is found to be the more efficient bleaching of the GLPC (5.14 eV) by the KrF laser compared to that by the ArF laser.
Samples of synthetic fused silica have been implanted at room temperature with silicon ions of energy 1.5 MeV. Fluences ranged from 1011 to 1013 cm−2. Samples were probed using variable‐energy positron annihilation spectroscopy. The Doppler‐broadening S parameter corresponding to the implanted region decreased with increasing fluence and saturated at a fluence of 1013 cm−2. It is shown that the decrease in the S parameter is due to the suppression of positronium (Ps) which is formed in the preimplanted material, due to the competing process of implantation‐induced trapping of positrons. In order to satisfactorily model the positron data it was necessary to account for positron trapping due to defects created by both electronic and nuclear stopping of the implanted ions. Annealing of the 1013 cm−2 sample resulted in measurable recovery of the preimplanted S parameter spectrum at 350 °C and complete recovery to the preimplanted condition at 600 °C. Volume compaction was also observed afterimplantation. Upon annealing, the compaction was seen to decrease by 75%.